An optical cell buffer (OCB) for use in photonic ATM switch, is needed in order to resolve contention between optical cells. A 320-Gb/s-throughput switch system with 32 wavelength channels requires a buffer size of 13 and a wavelength bandwidth of 25 nm. We developed an optical cell buffer with a four-nested-taps configuration and fabricated it with electroabsorption gates and gain clamped optical amplifiers. The output level variation, which determines the stability of operating condition, is less than 2.4 dB under typical conditions and the insertion loss variation is suppressed to within 5 dB. This OCB can be used in a 320-Gb/s photonic ATM switch.

We propose novel all-optical functional devices using waveguide X-junctions with localized third order optical nonlinearity, where one branch is made from a Kerr-like nonlinear material and the rest are made from linear ones. All-optical switching operations can be obtained because of bistable like nonlinear dispersion characteristics in linear and nonlinear coupled guided-wave systems. The performances of the devices are analyzed by the Beam Propagation Method (BPM) modified for nonlinear waveguides combined with the nonlinear normal mode analysis. The methods to construct the waveguides with localized nonlinearity are also discussed by utilizing the technologies for the selective control of a band-gap energy of semiconductor Multi Quantum Well (MQW) structures and the performances of the designed devices are presented.

We propose and demonstrate for the first time in our knowledge, an optical switch circuit architecture furnishing with the "Bridge and Switch" function, conforming to ITUT-T Recommendation G. 841 Annex A for optical Add-Drop Multiplexers (ADMs) in WDM four-fiber ring networks. This function enables optical ADMs to revert automatically from the switching state to their idle state just after the recovery of failure, that is indispensable for the extra traffic accommodation to enhance efficiency of the network operation. We have developed the optical ADM nodes employing the proposed optical switch circuit for each wavelength, arrayed-waveguide gratings (AWGs) and Er-doped fiber amplifiers. In the demonstration, transmission characteristics of the cascaded optical ADM nodes without regenerative repeaters have been verified at first. We have confirmed the ring protection and the automatic protection switching (APS) sequence which includes the automatic reversion in the optical ADM nodes with proposed optical switch circuits.

The tera-bit order capacity of ultrahigh-speed and wide-band networks will become necessary to provide highly advanced multimedia services. In conventional networks, electronic circuits limit the speed capability of the networks. Consequently, all-optical networks are essential to realize ultrahigh-speed and wide-band communications. In this paper, we propose the configuration of an all-optical code division multiplexing (CDM) switching network based on self-routing principles and the structure of a nonlinear all-optical switching device as one of the key components for the network. We show that the required performances of the optical devices used in the CDM switching fabric are lower than those used in the TDM and illustrate the basic transmission characteristics of the switching device utilizing FD-BPM. To evaluate the multiplexing performance, we demonstrate the maximum number of channels under an error-free condition and the BER characteristics when the Gold sequence is applied as one of the CDM code sets, and show that the network of the sub-tera-bit order capacity is realizable by adopting TDM, WDM and CDM technologies. We also illustrate the packet assembly method suitable for self-routing transmissions and one of network architectures where the proposed switching fabric can be exploited.

State of the arts on guided-wave optical switch arrays are reviewed. In this paper, electro-optic Ti:LiNbO3 devices are mainly described in comparison with crosspoint switch element structures and switch array architectures. Packaging technologies and stability problems are discussed for practical system applications. Recent development on other materials such as semiconductor waveguides, thermo-optic glass/polymer waveguides are also reviewed briefly.

We examine crossing waveguides with three channels consisting of nonlinear material by means of FD-BPM (Finite Difference Beam Propagation Method). Specifically, we investigate how the insertion of a multimode waveguide into the crossing section of both 13 and 23 structures influences the switching characteristics of output power. We then confirm that these structures can be favorably applied to a wide variety of all-optical devices for integrated optics such as intensity-dependent optical switches, optical power distributors and so on.

This paper describes the recently developed 816 delivery and coupling switch (DC-switch) boards for constructing a 320-Gb/s throughput (2. 5 Gb/s 8 multiplexed wavelengths 16 incoming/outgoing link pairs) optical path cross-connect (OPXC) system based on wavelength path (WP) and virtual wavelength path (VWP) schemes. The DC-switch-based OPXC system, compared with conventional space division switch (SD-switch)-based OPXC system architecture, is shown to be superior in terms of; i) high link modularity, ii) upgradability from WP network to VWP network, iii) better transmission characteristics, and iv) lower total switching power consumption. Therefore, the DC-switch-based OPXC system can realize cost-effective optical path networks. The developed DC-switches exploit the silica-based planar lightwave circuit (PLC) technologies, and DC-switch board size is 300330 mm2 (one switch). The worst values of the insertion loss of the board, ON/OFF ratio, and polarization dependent loss are 14. 5 dB, 34 dB and 0. 5 dB, respectively. Moreover, even though switching is realized by thermo-optic effects, the optical output level varies by only 0. 7 dB and 0. 8 dB for ON- and OFF-state signals, respectively, when the environmental temperature is varied from 5 to 65 .

In this paper, we discuss configurations of photonic ATM (Asynchronous Transfer Mode) switches and their advantages in terms of the number of optical switching devices to be implemented on the system, the number of wavelengths, throughput, broadcast function etc. In particular, we focus on photonic ATM switch architectures which can be built in the near future; that is, with presently available optical and electrical devices. For example, we assume the optical devices such as optical gate switches with 40 dB on/off ratio. In this context, we evaluate 17 types of photonic ATM switches; they are 6 types of input buffer type switches, 6 types of output buffer type switches, 4 types of shared buffer switches, and 1 proposed type. From our evaluation, for cell switching, wavelength division switching technologies are desirable compared with space division switching technologies in the sense that the former enables us to build a photonic ATM switch with the less number of optical gate switches. Furthermore, we propose a switch architecture equipped with optical delay line buffers on outputs and electric buffers on inputs. We show that our switch architecture is superior in the number of required optical gate switch elements under the given conditions.

A two-dimensional receiver OEIC array having an address selector for highly parallel interprocessor networks has been realized. The receiver OEIC array consists of two-dimensionally arranged 1616 (256) optical receiver cells with switching transistors, address selectors (decoders), and a comparator. Each optical receiver comprises a pin PD and a transimpedance-type HBT amplifier. The HBT has an InP passivation structure to suppress the emitter-size effect, which results in the improvement of current gains, especially at low collector current densities. The receiver OEIC array was fabricated on a 3-inch diameter InP substrate with pin/HBT integration technology. Due to the function of address selection, only one cell is activated and the other cells are mute, so the receiver OEIC array shows low crosstalk and low power consumption characteristics. The array also shows a 266-Mb/s data transmission capability. This receiver OEIC array is a most complex InP-based OEIC ever reported. The realization of the two-dimensional receiver OEIC array promises the future interprocessor networks with highly parallel optical interconnections.

We propose an nn optical switch that is suitable for flexible and reliable optical access networks and for reconfigurable optical inter-module connections in large-scale processing systems. The switch consists of an intersecting waveguide matrix, matching oil, and microactuators. Switching is based on the movement of oil due to capillary pressure, which is controlled by the microactuator. The necessary switching conditions were calculated and the results showed that both the oil volume and the microactuator position must be controlled. A trial optical switch was fabricated to test the switching principle, and switching and self-holding were both confirmed. These results show the feasibility of a very small self-holding nn optical switch that uses a waveguide matrix and microactuators made by using microfabrication technologies.

This paper describes the fabrication of micro-pipes and their applications to splicing parts and optical switches using single-mode fibers. Micro-pipes having almost the same inner diameter of bare fiber (125 µm) and lengths of around 5 mm are successfully mass-produced by using micromachining technology. We fabricate various kinds of metal pipes such as Au, Cu, Ni, and an FeNi alloy by selecting the appropriate electro-plating bath. We use an Au micro-pipe having a small slitted portion running along its axis (slitted micro-pipe) to splice single-mode fibers. We also use an FeNi alloy micro-pipe to construct a single-mode fiber switch. These new single-mode fiber devices employing micro-pipes show excellent optical and mechanical characteristics. Splicing losses are in the range of 0.2-0.4 dB. The developed 1 2 latching type single-mode fiber switches exhibit a low insertion loss of 0.35 dB, a minimum switching speed of 2 ms with a driving power of 9 mW, and stable operation for more than 108 switchings without damage. A practical application of the developed switch for testing optical devices is also demonstrated.

This paper describes the design, characteristics, and applications of newly developed latching-type 1 2 and 1 8 single-mode fiber switches. These switches have been successfully fabricated using micromachine technology. To reduce insertion loss and light reflection, an index-matching oil is injected into the switches. The fabricated 1 2 switches exhibit a low insertion loss of 0.31 dB, high return loss of 51 dB, relatively fast switching speed of 2 ms, and low driving power of 9 mw. Switching operation is stable over 108 switching times. A practical 1 8 single-mode fiber switch was also constructed using seven 1 2 switches cascaded in three stages. The fabricated 1 2 and 1 8 switches have been applied to an NTT multichannel video distribution FTTH system to enhance system reliability.

We propose a novel architecture (Switched Access Star: SAS) using an optical switch for access networks and prove its operating principle experimentally. In this architecture, the multiple optical network units (ONUs) in subscriber premises are connected to one optical subscriber unit (OSU) in a central office through an optical switch. SAS can increase the number of accommodated ONUs, the transmission line length, and the capacity per ONU. Moreover, this architecture does not need encryption or ID/passwords. SAS can reduce system cost and yield flexible transmission capacities and realize easy management and maintenance of optical transmission lines.

The complex refractive indices n-jχ of typical magnetic fluids were evaluated for the sake of utilizing them as optical materials. Transmission and reflection spectra were measured in the wavelength range of 0.6-1.6 µm by using monochromators. Magnetic fluids were put into glass cells of 2.5-14-µm thickness for transmission measurement. Due to the absorption by magnetic fluids, the transmittance decreased notably with the increase of the sample thickness. The extinction coefficient χ was evaluated from the dependence of the transmittance on the sample thickness. χ was found to vary between 0.003 and 0.03 depending upon wavelength. The refractive index n was evaluated by fitting theoretical curves to the reflectances that were measured for various incident angles. n was found to vary between 1.6 and 1.7 depending slightly on wavelength. Since a magnetic fluid is a composite of ferrite particles and a solvent, the refractive index can be calculated by using the effective medium theory. The calculated value agreed well with the experimental value. Preliminary experiment of optical switching was also demonstrated by utilizing the mobility of a magnetic fluid.

A novel series-tapered nonlinear directional coupler is proposed to improve all-optical switching characteristics. Its switching characteristics are analyzed by using a beam propagation method based on the Galerkin's finite element technique. It is presented that the critical power of the series-tapered nonlinear directional coupler is smaller than conventional uniform symmetric and tapered nonlinear directional couplers.

Various approaches on optical network systems using wavelength-division multiplexing (WDM) technique have been proposed. It is difficult to make a scale of WDM network larger since a number of the optical wavelength which can be used is limited. In order to make easily larger scale of network, multi-hop WDM network have been proposed. We have studied 2-hop network: RookNet which has simple routing algorithm and high network throughput. Nodes in RookNet are divided into row groups and column groups and are placed in a mesh form. Packets are transferred between nodes over 1-hop or 2-hops. The 2-hop transfer means that a source node sends packets to a destination node via a relay node. When 2-hop traffic increases, relay processing time in a relay node is increasing. This is the reason that network throughput becomes low. To solve this problem is very important. In this paper, we show RookNet rearrangement algorithm which replaces location of node within group so as to decrease the 2-hop traffic and to maintain high network throughput. Proposed rearrangement algorithm can achieve improvement of 10 percent in terms of throughput. We also propose RookNet configuration which discriminates optical wavelength and subcarrier effectively in order to decrease the relay processing time.

We analyze all-optical switching property of a nonlinear directional coupler (NLDC) having an MQW coupling layer with both nonlinear and linear losses, and examine the effect of nonlinear losses. We use the Galerkin finite element method accompanied by a prodictor-corrector algorithm. The propagation loss along the strongly-coupled NLDC decreases with increasing nonlinear absorption coefficient due to saturation in absorption. A propagation loss of 8.18 dB or 2.38 dB in the bar state of the cross state is much smaller than the bulk loss of MQW structure which exceeds 50 dB. The nonlinear losses lengthen the coupling length and bring it close to that of a lossfree NLDC, while the linear losses shorten. It is found that the property of the cross state is greatly improved by counting the nonlinear losses: The cross-state output power and the output power ratio of two waveguides increase, and the cross state input power, that is, the switching power decreases.

Wavelength-division multiplexing (WDM) optical switching networks are one of most attractive technologies in optical interconnections. By combining with time-division multiplexing (TDM) and space-division multiplexing (SDM) technologies, remarkably high-throughput interconnections may be accomplished. In this paper, we propose WDM switching networks with time-division multiplexed optical signals by using free-space optics. We also propose novel WDM interconnections, including multiple-wavelength light-sources, optical fibers and wavelength-selectable detectors. We successfully confirmed basic principles for the WDM interconnections.

For an application to the optical signal processing devices, we propose the optical X coupler which consists of two bending waveguides and a nonlinear dielectric region. To analyze this structure accurately we utilized the iterative finite difference beam propagation method (iterative FD-BPM). In this paper the formulation of the iterative FD-BPM for one wave and two waves cases are presented, respectively. We investigate following two cases. First, we consider the case that the light is launched into one of the input ports. We calculate the evolutions of the field amplitude and the transmission characteristics for the input power. Second, we consider the case that the signal light with the constant power is launched into one of the input ports and that the control light with the wavelength different from that of the signal light is launched into another input port. We calculate the evolutions of the field amplitude and the transmission characteristics of the signal light for the power of control light. As a result of the analysis, we show that all-optical switching operation is possible in the proposed structure.

Numerical simulations for the (3+1)-dimensional optical-field dynamics of nonstationary pulsed beams that propagate down Kerr-like nonlinear channel waveguides are carried out for what is to our knowledge the first time. Time-resolved intrapulse switching due to spontaneous symmetry breaking of optical fields from a quasilinear symmetric field to a nonlinear asymmetric field is analyzed. A novel instability phenomenon triggered by the symmetry breakdown is found.